Injection Packers
Complete range of injection packers for crack repair, structural rehabilitation, and waterproofing — from drill-in steel mechanical packers to surface-mounted adhesive ports and no-drill wedge packers.
Steel, Aluminium and Brass Packers
High-pressure mechanical drill packers manufactured from steel, aluminium, and brass. Designed for high-pressure polyurethane and epoxy injection in concrete crack repair, waterproofing, and structural rehabilitation.
Steel Injection Packers
High Pressure Steel Mechanical Injection Packers for concrete crack repairs, waterproofing, rehabilitation of concrete structures, and basement leak sealing. Compatible with high pressure injection pumps, suitable for both polyurethane and epoxy injection.
Aluminium Injection Packers
High Pressure Aluminium Mechanical Injection Packers for concrete crack repairs, waterproofing, rehabilitation of concrete structures, and basement leak sealing. Lightweight aluminium construction compatible with high pressure injection pumps.
Surface Adhesive Packers
Surface Adhesive Packers (Surface Packer Ports) are used for epoxy injection at low injection pressures. Glued to the concrete surface using epoxy adhesive, they feature non-return nipples to prevent resin flow-back. Ideal for hairline to wider cracks in dry conditions.
Steel Injection Packer with Conical Head Nipple
Steel drill injection packer with conical head nipple and special adhesive rubber sleeve. Designed for high-pressure polyurethane and epoxy resin injection in surface and crack injection applications on concrete and masonry.
Steel Injection Packer with Flat Head Nipple
Steel drill injection packer with flat head nipple and extended adhesive rubber sleeve. Purpose-built for crack and surface injection in brickwork, hollow masonry, and double-leaf walls where the longer sleeve and low-profile flat nipple deliver a better seal.
One Day Packer
Single-use steel injection packer with a built-in double non-return valve, allowing the packer to be removed and the hole closed off on the same day the resin is injected. Designed for pressure injection of wet and dry cracks and for horizontal sealing grouting.
Plastic Packers
Plastic drive-in, lamella, wedge, adhesive, and injection-hose packers. Lightweight, corrosion-free, and engineered for fast installation in concrete, masonry, natural stone, and re-injectable waterstop systems.
Adhesive Packer
Surface-glued plastic adhesive packer with M8 internal thread and an enclosed steel conical M8 nipple. Used for crack injection on substrates that may not be drilled into for structural or aesthetic reasons. Bonds directly to the component surface over the crack with epoxy paste.
Lamella Impact Packer 14mm
Plastic lamella drive-in injection packer (14 × 100 mm) for crack injection in concrete and masonry. Driven into a pre-drilled 14 mm hole with a hammer — the flexible plastic lamellae compress and grip the borehole wall, providing a pressure-tight seal without mechanical tightening. Available with or without integrated non-return check valve.
Lamella Impact Packer 18mm
Plastic lamella drive-in injection packer (18 × 120 mm) with flat-head nipple and cross-slider valve. Designed for veil and curtain injection of gels, resins, and microemulsions to seal ground-contact structures such as cellars, tunnels, and channels. Includes a gel-pipe holder for direct connection of 10 mm gel injection pipes.
Progressive Lamella Drive-In Packer
Slim-diameter plastic drive-in packer with progressively-sized lamellae and a screwed-in steel M6 cone nipple. Designed for crack injection in concrete, masonry, and natural stone. Available in two sizes — narrower for fine cracks and tight spaces, wider for higher injection flow rates.
Steel Wedge Packer
Compact steel wedge packer with a screwed-in steel M5 cone nipple and integrated check valve. Driven directly into the crack — no drilling required. Suitable for crack injection in concrete, granite, hollow block, brick, sandstone, and wood. Rated for injection pressures up to 50 bar.
Injection Hose Packer
HO-END 6 plastic injection-hose connector packer for terminating injection hose loops (re-injectable waterstops) at construction joints. Connects the embedded injection hose to the injection gun via an M6 × 1 or 1/4 thread, providing a controlled inlet point for the resin or grout to be pushed through the embedded hose.